Underground Service Locating: AS 5488 Quality Levels Explained

Underground service locating is how a surveyor finds the pipes and cables buried on a site. In Australia, the results are graded using Australian Standard AS 5488, which has four quality levels.

The levels run from QL-D, which is based on records only, to QL-A, where the service is uncovered and surveyed. This guide explains each one in plain English, so you can work out what your project on the Gold Coast or the Fraser Coast needs.

Each level builds on the one below it. A QL-B investigation, for example, also includes the QL-C and QL-D work.

What Is AS 5488?

AS 5488 is the Australian Standard for classifying underground service information. It was first published by Standards Australia in 2013 and revised in 2022. Part 1, AS 5488.1:2022, sets out how underground service information is classified. Part 2, AS 5488.2, covers subsurface utility engineering more broadly.

In simple terms, the standard gives everyone the same way to say how reliable a service location is. When your designer, engineer or certifier sees a quality level on your plan, they know how the service was found.

The Four Quality Levels at a Glance

Only QL-B and QL-A carry numbers. QL-D and QL-C give no spatial tolerance on the service itself.

Level Accuracy Method
QL-D No spatial tolerance. Indicative location only. Records search (BYDA, council, asset owner plans and GIS)
QL-C No absolute tolerance. The minimum requirement is relative spatial position. Surface features surveyed and matched to the QL-D records
QL-B ±300 mm horizontal and ±500 mm vertical (relative) Electromagnetic (EM) tracing and ground penetrating radar (GPR)
QL-A ±50 mm horizontal and vertical (absolute), at the exposed point only Vacuum excavation to expose the service, then survey

QL-D: Records Only

We check old plans. Nothing is checked on site.

  • How it is done: We collect plans from Before You Dig Australia (BYDA), council and the utility owners, and show the indicative locations on your site plan.
  • What you get: A rough idea of where services are expected to be, with no guaranteed accuracy. The date and source of the information are recorded.
  • Best for: Early feasibility and planning, or when you only need a general awareness of services.

QL-C: Records Plus Surface Features

We match the plans to things we can see on site, like pit lids and valves.

  • How it is done: We survey visible features such as pit lids, valves, hydrants and meters, and match them to the records.
  • What it means for you: The surface features are accurately positioned. The line drawn between them is an interpretation, not a measured location, because a buried service can wander away from the features above it.
  • Best for: Concept design, scoping and early cost estimates.

QL-B: Detected With Equipment

We scan the ground to find pipes and cables, then mark them. This is the most common level for design work.

  • How it is done: A specialist locator scans the site with electromagnetic (EM) equipment, which traces metal services and cables, and ground penetrating radar (GPR), which helps find pipes that are not metal. Services are marked on the ground and then surveyed onto your plan.
  • Accuracy: Within ±300 mm horizontally and ±500 mm in depth. The date, the information source and the locating method are recorded.
  • Limits: Some soils, especially clay and wet or salty ground, reduce what the equipment can detect. Plastic pipes without a tracer wire can be hard to find. Depths are estimates.
  • Best for: Detailed design, clash checks, build-over applications and most council and utility work.

QL-A: Exposed and Confirmed

We carefully uncover the service so we can see it and measure it. QL-A is the only level where a service is confirmed.

  • How it is done: Test holes are positioned from the QL-B locate. Each service is exposed with a vacuum excavation truck, which uses water or air instead of digging tools. Its depth, size and material are then surveyed and photographed.
  • Accuracy: Within ±50 mm horizontally and vertically, but only at the exposed point. Between test holes, the service is shown at the level it was located to.
  • On the plan: Depth labels carry the level, so “0.58A” means 580 mm deep, confirmed at QL-A.
  • Best for: Critical crossings, deep services near footings and final design checks.

Which Quality Level Do You Need?

Most sites do not need QL-A everywhere. A cost-effective approach is QL-B across the whole site, with QL-A test holes only where hitting a service would be costly or dangerous.

Check your design or council conditions for the level required. Your quote will also state which level applies to your job. If you are unsure, ask your designer, engineer or certifier, or talk to us.

QL-B depths are estimates. If a depth matters for your design, ask about QL-A test holes.

No locating method can guarantee every service is found, particularly undocumented services. Always dig with care.



Frequently Asked Questions

FAQs

Is a Before You Dig Australia search the same as underground service locating?

No. A BYDA search gives you plans from the asset owners, which is QL-D, records only. It shows where services are expected to be, not where they actually are.

Is QL-A always better than QL-B?

QL-A is the most accurate, but only at each exposed point. For most sites, QL-B across the whole site with QL-A test holes in the critical spots is a better fit.

Can plastic pipes be found?

Sometimes. Plastic pipes without a tracer wire can be hard to find. GPR helps, but the results depend on the ground.

Other Services

services


Need a reliable cadastral surveyor for your next project? Here's how we can help.


Accurate Lease Plans and Surveys in Queensland

Accurate Lease Plans and Surveys in Queensland

In Queensland, it is a legal requirement to register all long-term and high-value lease agreements and plans with the Titles Office. Only a cadastral surveyor can prepare a Lease Plan. Let us handle it for you.

Boundary Identification Survey Services in Queensland

Boundary Identification Survey Services in Queensland

Boundary marking is what we do. We are qualified to mark boundaries in New South Wales and Queensland. Our surveyors can mark property and easement boundaries for you at any stage of your development.

Form 12 Certification for Boundary Setbacks on the Gold Coast & Fraser Coast

Form 12 Certification for Boundary Setbacks on the Gold Coast & Fraser Coast

We can provide you with a Form 12, a certificate that involves marking the property boundaries before work is done. It is generally required for new buildings and renovations, including carports, sheds, pools, and even fences.

For all work big and small, get in touch today for a free quote.

browse our projects

our work


At Kaymak Survey, we like to let our work speak for itself. Take a look at some of our previous projects below.

Underground Service Locating on the Gold Coast and the Fraser Coast

contact

Working closely with local service locating companies we can plot your sewer and water mains to the accuracies council requires.

Kaymak Survey is a cadastral and engineering survey practice servicing the Gold Coast and the Fraser Coast.

Tell us what you are planning and we will let you know which quality level suits your site.

"*" indicates required fields